# Suspension Geometry and Computation

• ID: 1265975
• Book
• 434 Pages
• John Wiley and Sons Ltd
1 of 5
Revealing suspension geometry design methods in unique detail, John Dixon shows how suspension properties such as bump steer, roll steer, bump camber, compliance steer and roll centres are analysed and controlled by the professional engineer. He emphasizes the physical understanding of suspension parameters in three dimensions and methods of their calculation, using examples, programs and discussion of computational problems. The analytical and design approach taken is a combination of qualitative explanation, for physical understanding, with algebraic analysis of linear and non–linear coefficients, and detailed discussion of computer simulations and related programming methods.
• Includes a detailed and comprehensive history of suspension and steering system design, fully illustrated with a wealth of diagrams.
• Explains suspension characteristics and suspension geometry coefficients, providing a unique and in–depth understanding of suspension design not found elsewhere.
• Describes how to obtain desired coefficients and the limitations of particular suspension types, with essential information for suspension designers, chassis technicians and anyone else with an interest in suspension characteristics and vehicle dynamics.
• Discusses the use of computers in suspension geometry analysis, with programming techniques and examples of suspension solution, including advanced discussion of three–dimensional computational geometry applied to suspension design.
• Explains in detail the direct and iterative solutions of suspension geometry.
Note: Product cover images may vary from those shown
2 of 5
Preface.

1 Introduction and History.

1.1 Introduction.

1.2 Early Steering History.

1.3 Leaf–Spring Axles.

1.4 Transverse Leaf Springs.

1.5 Early Independent Fronts.

1.6 Independent Front Suspension.

1.7 Driven Rigid Axles.

1.8 De Dion Rigid Axles.

1.9 Undriven Rigid Axles.

1.10 Independent Rear Driven.

1.11 Independent Rear Undriven.

1.12 Trailing–Twist Axles.

1.13 Some Unusual Suspensions.

References.

2.1 Introduction.

2.7 Path Analysis.

2.8 Particle–Vehicle Analysis.

2.9 Two–Axle–Vehicle Analysis.

2.12 Logger Data Analysis.

References.

3.1 Introduction.

3.2 Isolated Ramps.

3.3 Isolated Bumps.

3.4 Sinusoidal Single Paths.

3.6 Fixed Waveform.

3.7 Fourier Analysis.

References.

4 Ride Geometry.

4.1 Introduction.

4.2 Wheel and Tyre Geometry.

4.3 Suspension Bump.

4.4 Ride Positions.

4.5 Pitch.

4.5 Roll.

4.7 Ride Height.

4.8 Time–Domain Ride Analysis.

4.9 Frequency–Domain Ride Analysis.

4.10 Workspace.

5 Vehicle Steering.

5.1 Introduction.

5.2 Turning Geometry – Single Track.

5.3 Ackermann Factor.

5.4 Turning Geometry – Large Vehicles.

5.5 Steering Ratio.

5.6 Steering Systems.

5.7 Wheel Spin Axis.

5.8 Wheel Bottom Point.

5.9 Wheel Steering Axis.

5.10 Caster Angle.

5.11 Camber Angle.

5.12 Kingpin Angle Analysis.

5.13 Kingpin Axis Steered.

5.14 Steer Jacking.

References.

6 Bump and Roll Steer.

6.1 Introduction.

6.2 Wheel Bump Steer.

6.3 Axle Steer Angles.

6.4 Roll Steer and Understeer.

6.5 Axle Linear Bump and Roll Steer.

6.6 Axle Non–Linear Bump and Roll Steer.

6.7 Axle Double–Bump Steer.

6.8 Vehicle Roll Steer.

6.9 Vehicle Heave Steer.

6.10 Vehicle Pitch Steer.

6.11 Static Toe–In and Toe–Out.

6.12 Rigid Axles with Link Location.

6.13 Rigid Axles with Leaf Springs.

6.14 Rigid Axles with Steering.

References.

7 Camber and Scrub.

7.1 Introduction.

7.2 Wheel Inclination and Camber.

7.3 Axle Inclination and Camber.

7.4 Linear Bump and Roll.

7.5 Non–Linear Bump and Roll.

7.6 The Swing Arm.

7.7 Bump Camber Coefficients.

7.8 Roll Camber Coefficients.

7.9 Bump Scrub.

7.10 Double–Bump Scrub.

7.11 Roll Scrub.

7.12 Rigid Axles.

References.

8 Roll Centres.

8.1 Introduction.

8.2 The Swing Arm.

8.3 The Kinematic Roll Centre.

8.4 The Force Roll Centre.

8.5 The Geometric Roll Centre.

8.6 Symmetrical Double Bump.

8.7 Linear Single Bump.

8.8 Asymmetrical Double Bump.

8.9 Roll of a Symmetrical Vehicle.

8.10 Linear Symmetrical Vehicle Summary.

8.11 Roll of an Asymmetrical Vehicle.

8.13 GRC and Latac.

8.14 Experimental Roll Centres.

References.

9 Compliance Steer.

9.1 Introduction.

9.2 Wheel Forces and Moments.

9.3 Compliance Angles.

9.4 Independent Suspension Compliance.

9.5 Discussion of Matrix.

9.6 Independent–Suspension Summary.

9.7 Hub Centre Forces.

9.8 Steering.

9.9 Rigid Axles.

9.10 Experimental Measurements.

References.

10 Pitch Geometry.

10.1 Introduction.

10.2 Acceleration and Braking.

10.3 Anti–Dive.

10.4 Anti–Rise

10.5 Anti–Lift.

10.6 Anti–Squat.

10.7 Design Implications.

11 Single–Arm Suspensions.

11.1 Introduction.

11.2 Pivot Axis Geometry.

11.3 Wheel Axis Geometry.

11.4 The Trailing Arm.

11.5 The Sloped–Axis Trailing Arm.

11.6 The Semi–Trailing Arm.

11.7 The Low–Pivot Semi–Trailing Arm.

11.8 The Transverse Arm.

11.9 The Sloped–Axis Transverse Arm.

11.10 The Semi–Transverse Arm.

11.11 The Low–Pivot Semi–Transverse Arm.

11.12 General Case Numerical Solution.

11.13 Comparison of Solutions.

11.14 The Steered Single Arm.

11.15 Bump Scrub.

References.

12 Double–Arm Suspensions.

12.1 Introduction.

12.2 Configurations.

12.3 Arm Lengths and Angles.

12.4 Equal Arm Length.

12.5 Equally–Angled Arms.

12.6 Converging Arms.

12.7 Arm Length Difference.

12.8 General Solution.

12.9 Design Process.

12.10 Numerical Solution in Two Dimensions.

12.11 Pitch.

12.12 Numerical Solution in Three Dimensions.

12.13 Steering.

12.14 Strut Analysis in Two Dimensions.

12.15 Strut Numerical Solution in Two Dimensions.

12.16 Strut Design Process.

12.17 Strut Numerical Solution in Three Dimensions.

12.18 Double Trailing Arms.

13 Rigid Axles.

13.1 Introduction.

13.2 Example Configuration.

13.3 Axle Variables.

13.4 Pivot–Point Analysis.

13.7 Numerical Solution.

13.8 The Sensitivity Matrix.

13.9 Results: Axle 1.

13.10 Results: Axle 2.

13.11 Coefficients.

14 Installation Ratios.

14.1 Introduction.

14.2 Motion Ratio.

14.3 Displacement Method.

14.4 Velocity Diagrams.

14.5 Computer Evaluation.

14.6 Mechanical Displacement.

14.7 The Rocker.

14.8 The Rigid Arm.

14.9 Double Wishbones.

14.10 Struts.

14.11 Pushrods and Pullrods.

14.12 Solid Axles.

14.13 The Effect of Motion Ratio on Inertia.

14.14 The Effect of Motion Ratio on Springs.

14.15 The Effect of Motion Ratio on Dampers.

14.16 Velocity Diagrams in Three Dimensions.

14.17 Acceleration Diagrams.

References.

15 Computational Geometry in Three Dimensions.

15.1 Introduction.

15.2 Coordinate Systems.

15.3 Transformation of Coordinates.

15.4 Direction Numbers and Cosines.

15.5 Vector Dot Product.

15.6 Vector Cross Product.

15.7 The Sine Rule.

15.8 The Cosine Rule.

15.9 Points.

15.10 Lines.

15.11 Planes.

15.12 Spheres.

15.13 Circles.

15.14 Routine PointFPL2P.

15.15 Routine PointFPLPDC.

15.16 Routine PointITinit.

15.17 Routine PointIT.

15.18 Routine PointFPT.

15.19 Routine Plane3P.

15.20 Routine PointFP.

15.21 Routine PointFPPl3P.

15.22 Routine PointATinit.

15.23 Routine PointAT.

15.24 Routine Points3S.

15.25 Routine Points2SHP.

15.26 Routine Point3Pl.

15.27 Routine ′PointLP′.

15.28 Routine Point3SV.

15.29 Routine PointITV.

15.30 Routine PointATV.

15.31 Rotations.

16 Programming Considerations.

16.1 Introduction.

16.2 The RASER Value.

16.3 Failure Modes Analysis.

16.4 Reliability.

16.6 Data Sensitivity.

16.7 Accuracy.

16.8 Speed.

16.9 Ease of Use.

16.10 The Assembly Problem.

16.11 Checksums.

17 Iteration.

17.1 Introduction.

17.2 Three Phases of Iteration.

17.3 Convergence.

17.4 Binary Search.

17.5 Linear Iterations.

17.6 Iterative Exits.

17.7 Fixed–Point Iteration.

17.8 Accelerated Convergence.

17.9 Higher Orders without Derivatives.

17.10 Newton’s Iterations.

17.11 Other Derivative Methods.

17.12 Polynomial Roots.

17.13 Testing.

References.

Appendix A: Nomenclature.

Appendix B: Units.

Appendix C: Greek Alphabet.

Appendix D: Quaternions for Engineers.

Appendix E: Frenet, Serret and Darboux.

Appendix F: The Fourier Transform.

References and Bibliography.

Index.

Note: Product cover images may vary from those shown
3 of 5