Global SiC Wafer Polishing Market Trends and Insights
EV Inverter and Onboard-Charger Deployment
The SiC wafer polishing market benefits as SiC Metal-Oxide-Semiconductor Field-Effect Transistors (MOSFETs) become a preferred design choice for EV traction inverters using 800-volt battery systems. Their use is also extending to onboard chargers, where faster switching can support compact charging stages rated from 7 kW to 22 kW. ROHM introduced compact HSDIP20 SiC modules for onboard charger power factor correction in April 2025, reporting more than 3 times the power density of top-cooled discrete designs. BYD disclosed a 1,000 kW peak-charging platform in March 2025 that uses high-voltage SiC power chips. Tighter device geometry leaves less tolerance for subsurface damage, increasing the need for longer, more chemically active CMP steps. Onsemi reported resilient demand for SiC from Chinese and European EV customers in May 2025, despite uncertainty over US tariffs.Renewable-Energy Power-Conversion Demand
The SiC wafer polishing market also benefits from renewable energy systems that require efficient power conversion. Large solar inverters are adopting SiC devices because they can achieve system efficiency above 99%, compared with 98% to 98.5% for silicon Insulated Gate Bipolar Transistor (IGBT) designs. Full-power wind converters also benefit from lower thermal stress, particularly in offshore installations where maintenance costs are high. A 2025 review identified wide-bandgap semiconductors as important for integrating large shares of renewable energy into electricity systems and reducing conversion losses. Grid equipment often operates continuously at high voltage, so manufacturers require very low defect densities and high-purity final polishing. This requirement supports demand for colloidal silica finishing steps and qualified CMP consumables.Extreme Hardness, Brittleness, and Defectivity
The SiC wafer polishing market faces process constraints due to SiC's Mohs hardness of 9 and brittleness. Even optimized CMP slurries achieve material removal rates of only 4-7 µm/hour on the Si face. Surface defects can become dislocations in the epitaxial layer, reducing breakdown voltage and switching reliability in finished devices. This issue is more pronounced for 200 mm wafers, which carry a higher risk of edge roll and thickness variation than 150 mm wafers. A 2025 study found that ultrasonic chemical-corrosion approaches still require careful calibration to avoid creating new subsurface damage. These yield constraints limit the rate at which new polishing capacity converts into usable wafer supply.Other drivers and restraints analyzed in the detailed report include:
- Transition from 6-Inch to 8-Inch SiC Wafers
- Advanced Chemical Mechanical Polishing (CMP) Consumables and Surface-Quality Requirements
- Long Cycle Times and Low Material-Removal Rates
Segment Analysis
Polishing pads held 60.21% of the SiC wafer polishing market share in 2026 and are forecast to grow at a 38.93% CAGR through 2032. This reflects higher CMP step counts and rising pad consumption as wafer geometry requirements become more stringent. Pads play a central role in CMP because their pore structure, groove pattern, and hardness influence surface condition alongside slurry chemistry. The SiC wafer polishing market favors pad suppliers that can deliver stable performance across a range of wafer sizes. Fujibo Holdings held an estimated 80% global share of CMP soft pads, a category used in final SiC polishing.Fujibo announced an investment of JPY 8.7 billion (~USD 0.05 billion) at its Mibu-gawa factory in November 2025 to raise CMP soft-pad production by 60% by late fiscal 2028. The company is also building a JPY 6.5 billion research center in Taiwan, with an operational target in the first half of fiscal 2027, to work with Asian fabs on pad-and-slurry combinations. Abrasive powders remain important for initial grinding and lapping, where larger wafers require substantial material removal. Diamond slurries are used for intermediate mechanical polishing, while colloidal silica suspensions are used for final finishing. Colloidal silica is gaining relevance as surface roughness requirements move below 0.1 nm Ra.
Complete Report Scope:
- By Product Type
- Abrasive Powders
- Polishing Pads
- Diamond Slurries
- Colloidal Silica Suspensions
- Other Product Types
- By Process Type
- Mechanical Polishing
- Chemical-Mechanical Polishing (CMP)
- Electropolishing
- Chemical Polishing
- Plasma-Assisted Polishing
- Other Process Types
- By Application
- Power Electronics
- Light-Emitting Diodes (LEDs)
- Sensors and Detectors
- RF and Microwave Devices
- Other Applications
- By Geography
- Asia-Pacific
- China
- India
- Japan
- South Korea
- Rest of Asia-Pacific
- North America
- United States
- Canada
- Mexico
- Europe
- Germany
- United Kingdom
- France
- Italy
- Rest of Europe
- South America
- Brazil
- Argentina
- Rest of South America
- Middle East and Africa
- Saudi Arabia
- South Africa
- Rest of Middle East and Africa
- Asia-Pacific
Geography Analysis
Asia-Pacific held 40.38% of the SiC wafer polishing market share in 2026 and is forecast to grow at a 40.04% CAGR through 2032. China supports regional demand through investment in SiC manufacturing, large-scale EV deployment, and renewable energy expansion. The YOFC SiC wafer facility in Wuhan began production in 2025 with an annual capacity of 360,000 wafers, sufficient to supply chips for 1.44 million new-energy vehicles. China's 2025 tax policy notice includes polishing pads and slurries among the materials eligible for preferential treatment. Japan contributes through Fujibo, Fujimi, and JSR, while South Korea and Taiwan are working to qualify 200 mm SiC processes and strengthen co-development opportunities for materials suppliers.North America is a major market for SiC wafer polishing, encompassing wafer suppliers, device makers, and consumable developers. Wolfspeed's shift toward 200 mm substrate revenue supports recurring demand for qualified CMP products, while Entegris supplies Epic Power CMP pads and slurry-recycling systems for high-capacity fabs. US chip incentives support new wafer capacity requiring larger-format polishing tools and consumables, while Engis offers Grind-to-CMP solutions for 150 mm and 200 mm wafers. Compliance factors include OSHA requirements and EPA semiconductor air-emissions rules for slurry handling and waste treatment. EPA and OSHA renewed cooperation on chemical safety in January 2025, reinforcing chemical management standards across manufacturing sites.
Europe is expanding its role in SiC power-device production through Onsemi's planned integrated facility in the Czech Republic. The facility is expected to begin commercial operations in 2027 and will cover stages from crystal growth to finished devices. Infineon is transitioning its Kulim, Malaysia site from 150 mm to 200 mm wafer production, creating demand in Southeast Asia. The European Union's Critical Raw Materials Act supports upstream supply chains, while Brazil, Saudi Arabia, and India are increasing their focus on SiC power electronics through initiatives in renewable energy and semiconductors.
List of Companies Covered in this Report:
- 3M
- DuPont
- Engis Corporation
- Entegris
- FUJIBO HOLDINGS, INC.
- Fujimi Incorporated
- ILJIN DIAMOND CO., LTD.
- JSR Corporation
- Kemet International Limited
- Lapmaster Wolters
- Logitech Ltd.
- Pureon AG
- Saint-Gobain
- SKC
- Vibrantz
Additional Benefits:
- The market estimate (ME) sheet in Excel format
- 3 months of analyst support
Table of Contents
Companies Mentioned (Partial List)
A selection of companies mentioned in this report includes, but is not limited to:
- 3M
- DuPont
- Engis Corporation
- Entegris
- FUJIBO HOLDINGS, INC.
- Fujimi Incorporated
- ILJIN DIAMOND CO., LTD.
- JSR Corporation
- Kemet International Limited
- Lapmaster Wolters
- Logitech Ltd.
- Pureon AG
- Saint-Gobain
- SKC
- Vibrantz

